Dieser Shop benötigt aktiviertes JavaScript.
Receiver accessories (131 results)
Jeti Switch RCSW Switch Wireless switch for Jeti BEC stabilizers and central box Compatible devices: SBEC 40, DPS 40, SPS 20, DSM 10, Central Box 200, Central Box 400 and Master Switch Easily controllable with DC/DS transmitter Indication of the switching status by means of red LED For more comfort Offer
Jeti Power supply S BEC Power supply for receiver and servos Input voltages from 2S to 10S Li-XX cells possible Adjustment of output voltage from 5 to 8 V by jumper Also suitable for servos with higher voltages Maximum current of up to 12 A - ideally suited for medium and larger models
Jeti Anti-flash connector Anti Spark 5.5 mm Avoids the annoying and plug-destroying flashing when plugging the battery into the controller Support capacitors on the controller are protected ASC socket with special SMD resistors ASC socket is soldered to one of the controller cables (plus or minus, depending on personal pin assignment) Compatible with existing 5.5 mm gold plugs/sockets
Powerbox Systems Battery switch Pioneer + MicroSwitch 14 channel Powerful battery backer with high continuous load capacity Consistently double design of the power electronics Redundant electronic switch Full operability from the transmitter for PowerBox and Jeti Latest iGyro technology integrated, with the iGyro Sat as gyro sensor 9 independent gyro outputs for: 3x aileron, 3x elevator, 3x rudder
Carson LED RACE Light unit With a total of 12 LEDs Turn signal front left/right 3 mm and turn signal rear left/right 3 mm Front light left/right 5 mm (4 LEDs) Taillight/brake light left/right 5 mm (4 LEDs) Demomode Futaba plug-in system suitable for Tamiya models Offer
Jeti Switch SP 06 Suitable for switching purposes of auxiliary functions, such as onboard glow plugs, heating systems, lighting systems in model aircraft, model ships and model cars Switched loads can be of resistive, inductive or capacitive character Signaling of the switching time by means of an LED Input voltage up to 16 V
Powerbox Systems Sensor PBS-Vario Climb rate measurement with 0.1m/s accuracy Height measurement with 0.1m accuracy Temperature measurement Supports the following telemetry systems: PowerBox P²BUS, Jeti EX-Bus, Futaba S.BUS2 Supported remote control systems: PowerBox, Jeti, Futaba Operating voltage from 4 - 9 V Offer
Jeti Battery switch Central Box 220 + 2x Rsat2 + RCSW Wirelessly programmable via the device overview of the DC/DS transmitters Fused servo outputs (for 11 servos with ~30 kg actuating force and 4x ~50 kg) Battery connections 2x MPX plug-in system Rugged aluminum housing for extra cooling and protection Firmware upgradeable via Jeti USB adapter and Jeti Studio Up to 3 independent receiver inputs (R1, R2, E1/R3), up to 15 servo slots (suitable for DITEX servo telemetry) and up to 3 telemetry sensor inputs (E1/R3, E2/15, E3/14)
Jeti Switch RC Power Switch 10A To switch a model on and off Controllable with DC/DS transmitter Simply switch on using a safety switch on the transmitter, confirm the safety query and you're done Can be used as a replacement for a standard switch No more need to open the model Indication of the switching status by means of red LED
Jeti Switch DPS 40 Dual electronic switch with 2 battery inputs For switching supply voltages of receivers, servos, controllers and fuel pumps Higher vibration resistance and lower inherent contact resistance compared to mechanical switches, withstands an unlimited number of switching cycles High durability, as there are no moving parts such as contacts and are not susceptible to unexpected false tripping Operation by means of magnetic switch Can also be used for other DC switching tasks Offer
Jeti Power supply MAX BEC 2D plus EX Magnetic switch prevents mechanical wear due to on/off switching Supports switching by optional RC switch Large cooling body dissipates excess heat Programmable with JETIBOX Duplex EX compatible - setting of audible alarms for low input voltage or too high temperatures and real-time feedback (input/output voltage, temperature) possible with JETIBOX profi Redundant inputs for power supply and output with MPX socket for Duplex / Duplex EX receiver
Jeti Voltage controller Single BEC 1A For the supply of servos with a maximum voltage range of up to 6 volts up to the standard size on a HV receiving system Can also be used to supply multicopter or flight attitude control electronics without servos Due to its small dimensions and low weight, it is also suitable for small and medium-sized models or can be installed in a wide variety of model components (wings, tail units, fuselage) Applicable for servos with a force of up to 25 kg/cm Offer
Jeti Switch DSM 10 For switching two batteries connected to one receiver With receiver power supply switch Permanently measures batteries connected to the inputs Connects by means of hysteresis comparator either both to the output or to one of the two accumulators with the higher voltage Even a total failure does not affect operation Output consisting of an MPX connector for direct connection to the receiver
Jeti Voltage controller SBEC 30D EX Serves as power supply for receiver and servos Allows input voltages from 2S to 15S Li-XX cells Output voltage adjustable from 5 to 8.4 V (in 0.1 V steps) from Jeti DS/DC transmitter via EX bus or with JETIBOX Provides maximum current of 30 A Measures input and output voltage, flowing current and consumed capacitance - Data can be shown on the display of Jeti DS/DC transmitters and/or output via voice output With 1 battery input
Jeti Switch Universal Magnetic Switch Withstands almost an unlimited number of switching cycles, has lower internal resistance and higher vibration resistance than a mechanical switch High durability because there are no moving parts such as contacts 4 slots for the connection of three-core patch cables with JR/UNI connector system Slots divided into two pairs, one pair of the slots is galvanically isolated by an optocoupler Each pair with one non-inverted and one inverted output Provides the ability to turn multiple Jeti devices on or off simultaneously
Powerbox Systems Switch DigiSwitch V2 JR/JR Powerful electronic switch with lightweight and compact design Supported batteries: 2S LiPo, 2S LiIon, 2S LiFePo and 5 cells NiMH Operating voltage: 4.0 V - 9.0 V Output voltage: 6.0 V / 7.0 V / 7.6 V stabilized or unregulated Current carrying capacity: max. 10 A Telemetry support for CORE
Powerbox Systems Mounting frame MPX Socket, 6 pieces incl. screws Fits exactly on all M6 and MPX connectors as well as PowerBox MPX cables molded in with the hotmelt process (PIK power cables 0.35 mm² to 2.5 mm² and MPX area connectors One4two) 6 socket mounting frame made of solid ABS 12 screws included Installation depth: 8 mm Offer
Jeti Anti-flash connector Anti Spark 4.0 mm Avoids the annoying and plug-destroying flashing when plugging the battery into the controller Support capacitors on the controller are protected ASC socket with special SMD resistors ASC socket is soldered to one of the controller cables (plus or minus, depending on personal pin assignment) Compatible with existing 4 mm gold plugs/sockets Offer
Jeti Anti-flash connector Anti Spark 8.0 mm Avoids the annoying and plug-destroying flashing when plugging the battery into the controller Support capacitors on the controller are protected ASC socket with special SMD resistors ASC socket is soldered to one of the controller cables (plus or minus, depending on personal pin assignment) Compatible with existing 8 mm gold plugs/sockets
Jeti Micro switch magnetic 15A Suitable for switching the receiver power supply Maximum continuous current: 15 A Operating voltage: 4 - 8.4 V DC Light weight of 7 g Dimensions: 32 x 9 x 5 mm Offer
Jeti Battery switch Central Box 100 Up to 8 servo outputs (with overload protection) individually programmable, 1 telemetry sensor connectable without further expander and 1 battery input Each output individually configurable (channel assignment, trim etc.) Possibility to connect up to 2 receivers with serial interface (PPM, EX Bus) Measured values telemetry: consumed capacity, voltage, current of the receiver batteries and servo failure Easy setting changes via DC/DS transmitter Suitable for use with HV servos
Powerbox Systems Adapter PowerBox iGyro 1e Single axis MEMS sensor Integrated servo match and reverse function Regulatory algorithm specifically for fixed wing aircraft 16-bit processor for fast, high-resolution signal processing Heading or normal mode, switchable in flight Conventional PWM input and output signals Offer
Jeti Battery switch Central Box 320 with magnet switch Connections for up to 18 servos (HV-capable) with overload protection and DITEX telemetry support Possibility to connect up to 3 duplex receivers with serial communication EX telemetry support with integrated expander for up to 4 sensors Battery switch for 2 1-3S LiXX batteries with MPX high current connector Supply voltage: 4 - 14 V, Current: max. 25 A, Bec voltage: 5 - 8.4 V Magnetic switch included
Powerbox Systems Switch DigiSwitch V2 MPX/JR Powerful electronic switch with lightweight and compact design Supported batteries: 2S LiPo, 2S LiIon, 2S LiFePo and 5 cells NiMH Operating voltage: 4.0 V - 9.0 V Output voltage: 6.0 V / 7.0 V / 7.6 V stabilized or unregulated Current carrying capacity: max. 10 A Telemetry support for CORE Offer
Jeti Power supply DSM ESC To supply the receiver and the servos Combines the BEC supply of two speed controllers/regulators or a combination of receiver battery (backup battery) and one BEC controller to supply the receiving system Switching on/off by means of magnetic switch Optional RC switch can also be used for switching Offer
Jeti V-cable MPX For 2 diode-separated power supplies on one receiver Also suitable for the separation of backup battery and controller BEC With MPX connector system Cable length: 15 cm each Cable cross section: 1 mm² Supply voltage/current load: maximum 16 V / 12 A
Powerbox Systems Battery switch EVO with sensor switch Powerful battery backer with high continuous load capacity Consistent dual design of the power electronics Operating voltage: 4.0 - 9.0 V (intended for 2S LiXX or 5-cell NiMH batteries) Adjustable output voltage: 6 V, 7.4 V, 7.8 V, unregulated Dimensions: 89 x 55 x 18 mm Supported telemetry systems: P²BUS, S.BUS2, EX-Bus, SRXL2, M-Link, Hott, JR-DMS
Powerbox Systems Voltage controller V-Regulator BEC 5.3 V, 3 A Regulated output voltage of 5.3 V Continuous current up to 3 A, peak current up to 20 A (< 10 s) Operating voltage: 4 V - 9 V (ideal for 2S LiPo batteries) Large area milled aluminum heat sink Excellent for ignitions, small helicopters and smaller models with up to 8 servos Extremely slim design for small hulls
Jeti Battery switch Central Box 310 with 2x Rsat2 and RCSW Connections for up to 18 servos (HV-capable) with DITEX telemetry support Possibility to connect up to 3 duplex receivers with serial communication EX telemetry support with integrated expander for up to 4 sensors Battery switch for 2 1-3S LiXX batteries with MPX high current connector Supply voltage: 4 - 14 V, Current: max. 25 A, Bec voltage: 5 - 8.4 V Including 2x Rsat2 receiver and RCSW
Powerbox Systems Battery switch Pioneer + MicroMag 14-channel Powerful battery backer with high continuous load capacity Consistently double design of the power electronics Redundant electronic switch Full operability from the transmitter for PowerBox and Jeti 9 independent gyro outputs for: 3x aileron, 3x elevator, 3x rudder Operating voltage 4.0 V - 9.0 V
Powerbox Systems V-cable MicroMatch Servo match function on both outputs Direction of rotation, center and end points as well as frame rate of the outputs adjustable Fast reverse function as well as interference suppression and pulse amplifier function 16-bit processor for fast signal processing and 4096 steps resolution for latest servo generation High current carrying capacity, limited only by the plug connection Programmable via USB interface adapter (PC) or mobile terminal (using BlueCom adapter)
Powerbox Systems Mounting frame MPX Plug, 6 pieces incl. screws Fits exactly on all M6 and MPX connectors as well as PowerBox MPX cables molded in with the hotmelt process (PIK power cables 0.35 mm² to 2.5 mm² and MPX area connectors One4two) 6 connector mounting frames made of solid ABS 12 screws included Installation depth: 11 mm Offer
Jeti Switch SPS 20 Single electronic switch with 1 battery input For switching supply voltages of receivers, servos, controllers and fuel pumps Higher vibration resistance and lower inherent contact resistance compared to mechanical switches, withstands an unlimited number of switching cycles High durability, as there are no moving parts such as contacts and are not susceptible to unexpected false tripping Operation by means of magnetic switch Can also be used for other DC switching tasks
Jeti Switch RCSW Switch
OfferJeti Power supply S BEC
Jeti Anti-flash connector Anti Spark 5.5 mm
Powerbox Systems Battery switch Pioneer + MicroSwitch 14 channel
Hobbywing Voltage controller UBEC V2-Air 5A 2-8S
Carson LED RACE Light unit
OfferJeti Switch SP 06
Powerbox Systems Sensor PBS-Vario
OfferJeti Battery switch Central Box 220 + 2x Rsat2 + RCSW
Jeti Switch RC Power Switch 10A
Jeti Switch DPS 40
OfferJeti Power supply MAX BEC 2D plus EX
Jeti Voltage controller Single BEC 1A
Powerbox Systems Cable set PowerBox Premium one4three
OfferJeti Switch DSM 10
Castle Creations Power supply BEC Pro
Jeti Voltage controller SBEC 30D EX
Jeti Switch Universal Magnetic Switch
Powerbox Systems Switch DigiSwitch V2 JR/JR
Powerbox Systems Cable set PowerBox Premium one4one MR30
Powerbox Systems Mounting frame MPX Socket, 6 pieces incl. screws
OfferJeti Anti-flash connector Anti Spark 4.0 mm
OfferJeti Anti-flash connector Anti Spark 8.0 mm
Jeti Micro switch magnetic 15A
OfferJeti Mounting frame for Power Ion receiver batteries
OfferJeti Battery switch Central Box 100
Powerbox Systems Adapter PowerBox iGyro 1e
Powerbox Systems Battery switch Sensor V3 MPX/JR connection
OfferJeti Battery switch Central Box 320 with magnet switch
Powerbox Systems Switch DigiSwitch V2 MPX/JR
OfferJeti Power supply DSM ESC
OfferJeti V-cable MPX
Powerbox Systems Battery switch EVO with sensor switch
Powerbox Systems Voltage controller V-Regulator BEC 5.3 V, 3 A
Jeti Battery switch Central Box 310 with 2x Rsat2 and RCSW
Powerbox Systems Cable set PowerBox Premium one4two
Powerbox Systems Battery switch Sensor V3 JR/JR connection
Powerbox Systems Battery switch Pioneer + MicroMag 14-channel
OfferJeti Voltage controller Addcap 10AS
Powerbox Systems V-cable MicroMatch
Powerbox Systems Mounting frame MPX Plug, 6 pieces incl. screws
OfferJeti Switch SPS 20
