Developer boards & accessories (532 results)
- +120
Raspberry Pi Power pack SC1152 5 V, 5A, USB-C, white, Raspberry Pi 5- USB-C PD capable: 5 V 5 A / 9 V 3 A / 12 V 2.25 A / 15 V 1.8 A
- 1.2 m long cable with USB-C connector
- Input voltage: 230 V 50 Hz
- Dimensions: 87 x 43 x 95 mm
- Ideal for the Raspberry Pi 5
- +95
Raspberry Pi Developer board Raspberry Pi 5 4 GB- Broadcom BCM2712 SOC with 2.4 GHz 64-bit Arm Cortex-A76 quad-core CPU
- 4 GB DDR4 Ram
- Dual-band 802.11ac Wi-Fi and Bluetooth 5.0
- Two 4Kp60 HEVC capable micro-HDMI ports
- Standard 40-pin Raspberry Pi GPIO interface
- Power supply: external 5 V 5A power supply via USB-C (sold separately)
- +83Raspberry Pi Developer board Raspberry Pi 5 16 GB
- Broadcom BCM2712 SOC with 2.4 GHz 64-bit Arm Cortex-A76 quad-core CPU
- 16 GB DDR4 Ram
- Dual-band 802.11ac Wi-Fi and Bluetooth 5.0
- Two 4Kp60 HEVC capable micro-HDMI ports
- Standard 40-pin Raspberry Pi GPIO interface
- Power supply: external 5 V 5A power supply via USB-C (sold separately)
- +80Raspberry Pi Developer board Raspberry Pi 5 8 GB
- Broadcom BCM2712 SOC with 2.4 GHz 64-bit Arm Cortex-A76 quad-core CPU
- 8 GB DDR4 Ram
- Dual-band 802.11ac Wi-Fi and Bluetooth 5.0
- Two 4Kp60 HEVC capable micro-HDMI ports
- Standard 40-pin Raspberry Pi GPIO interface
- Power supply: external 5 V 5A power supply via USB-C (sold separately)
- +28
Raspberry Pi Active cooler SC1148, Raspberry Pi 5- Flat aluminum heat sink with fan
- Compatible with Raspberry Pi 5
- +17
Raspberry Pi Starter kit Raspberry Pi 4 Model B 8 GB- Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5 GHz, 8 GB LPDDR4-3200 SDRAM Ram
- Gigabit Ethernet (LAN), 2.4 GHz / 5.0 GHz IEEE 802.11ac Wlan, Bluetooth 5.0, BLE
- Raspberry Pi standard 40-pin GPIO header (backward compatible with older models)
- 2x Micro HDMI port, supports resolutions up to 4K
- 32 GB Micro SD card with pre-installed RasbianOS operating system
- Starter set including 32 GB micro SD card, power supply, case, Lan cable and HDMI cable
Also available in: - +134
Shelly Temperature sensor DS18B20 1-Wire- 1-Wire
- Accuracy (-10°C - 85°C): ±0.5°C
- 1 m cable
- Waterproof
SKU: 1018633Manufact. ID: Temperature sensor DS18B20 (1 meter)Category: Sensor developer boards CHF 3.90 - +26
Raspberry Pi Housing SC1160 with fan Black, Raspberry Pi 5- Robust plastic housing
- Cut-outs for all connections
- Fan included
- Compatible with the Raspberry Pi 5
- +30
Raspberry Pi Developer board Raspberry Pi Zero W 512 MB with GPIO header- Broadcom BCM2835 processor with 1 GHz
- 512MB RAM
- On-board WLAN and Bluetooth
- micro-SD slot, mini-HDMI Type C, 2x micro USB (1x power, 1x data)
- Assembled 40-pin GPIO connector
- Dimensions: 65 x 30 x 5 mm
- +67
Whadda Voltage regulator DC-DC Step Down LM2596S- Input voltage: 3 to 40 V DC
- Output voltage: 1.25 to 35 V DC
- Output current: Max. 2.5 A
- Chip: LM2596S
- Dimensions: 49 x 26 x 12 mm
- +3
Shelly Leak sensor cable- Water detection over the entire cable length for comprehensive protection
- Flexible placement, also ideal for hard-to-reach places
- Direct connection with Flood Gen4 for immediate functionality
- High sensitivity and fast response time thanks to conductive materials
- Supports automations for switching off devices
- Reusable and easy to clean, simply wipe dry after the alarm
- +30
Raspberry Pi Power pack 5.1 V 2.5 A, micro USB, to Pi Zero 1 / 2, Pi 3B- Suitable for Raspberry Pi 3B / 3B / 3A / 2B / Zero / Zero 2
- Output voltage: 5.1 V DC
- Current: 2.5 A
- 1.8 m long cable with Micro USB connector
- Input voltage: 100 - 240 V AC 50/60 Hz
- +52Raspberry Pi Developer board Raspberry Pi 5 2 GB
- Broadcom BCM2712 SOC with 2.4 GHz 64-bit Arm Cortex-A76 quad-core CPU
- 2 GB DDR4 Ram
- Dual-band 802.11ac Wi-Fi and Bluetooth 5.0
- Two 4Kp60 HEVC capable micro-HDMI ports
- Standard 40-pin Raspberry Pi GPIO interface
- Power supply: external 5 V 5A power supply via USB-C (sold separately)
- +13
M5Stack LED strip Digital RGB LED Strip SK6812 1 m- Programmable RGB LED strip with IP65 waterproof protection
- LED quantity: 60 LEDs
- LED strip width: 10 mm
- Lifetime: 30Kh
- Programming method: Arduino, UIFlow (Blockly, Python)
- HY2.0-4P adapter cable included
- +21
Raspberry Pi Developer board Pico 2WH- ARM Cortex-Processor
- Integrated graphic: No
- Interfaces: 4-pin (PWM), ADC, Bluetooth, GPIO, Micro-USB 1.1, SPI, UART, WLAN
- +10
Arduino Developer board Arduino UNO R4 WiFi- Renesas RA4M1 SoC with Arm Cortex-M4 32 bit 48 MHz processor, 32 KB SRAM, 256 KB flash memory
- Version with ESP32-S3 WiFi / Bluetooth BLE
- Compatible with all older Arduino UNO shields
- Input voltage: 6 - 24 V DC
- Interfaces: 14x digital pins, 6x PWM, 6x ADC, 1x 12 bit DAC, 1x SPI, 1x i2C, 1x CAN
- 12x8 LED matrix
- +233
Raspberry Pi Developer board Raspberry Pi 4 Model B 4 GB- Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5 GHz
- 4 GB LPDDR4-3200 SDRAM Ram
- Gigabit Ethernet (LAN), 2.4 GHz / 5.0 GHz IEEE 802.11ac Wlan, Bluetooth 5.0, BLE
- Interfaces: Micro-HDMI, USB 2.0, USB 3.0, WLAN, GPIO, Bluetooth, RJ-45 (1000Mbps)
- Raspberry Pi standard 40-pin GPIO header (backward compatible with older models)
- 2x Micro HDMI port, supports resolutions up to 4K
- +21
Whadda Jumper set (f - f), 30 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 30 cm each
- Suitable for standard plug-in boards (pitch: 0.1")
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +24
Whadda Jumper set (m - m), 30 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 30 cm each
- Male to male
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +17
Whadda Relay module 5 V compatible with Arduino- Control voltage: 5 V DC
- Maximum switchable voltage: 250 V AC / 30 V DC
- Maximum current: 10 A
- Relay contacts: COM, NO, NC
- Dimensions: 40 x 27 x 18 mm
- +1
Whadda Water pump 4.2 W, 5 - 12 V DC- Powerful mini water pump
- Voltage range: 5 V - 12 V DC
- Flow rate (maximum): 240 liters/hour
- Power consumption: 4.2 W at 12 V DC
- Outer diameter output / input 8 mm
- Lifetime: > 30,000 hrs
- +54
Whadda RFID card 10 piece- Frequency: 13.56 MHz
- Memory : 1 kb EEPROM
- Type: ISO14443 Type - A
- Operating temperature: -10 °C to 75 °C
- Can be rewritten up to 100000x
- +25Raspberry Pi Developer board Raspberry Pi 5 1 GB
- Broadcom BCM2712 SOC with 2.4 GHz 64-bit Arm Cortex-A76 quad-core CPU
- 1 GB DDR4 Ram
- Dual-band 802.11ac Wi-Fi and Bluetooth 5.0
- Two 4Kp60 HEVC capable micro-HDMI ports
- Standard 40-pin Raspberry Pi GPIO interface
- Power supply: external 5 V 5A power supply via USB-C (sold separately)
- +18
M5Stack Developer board ATOM Lite ESP32 IoT Development Kit- ESP32 240 MHz dual core processor with 520 KB SRAM
- Connectivity: USB-C, Bluetooth, Wifi, infrared
- 4 MB Flash Memory
- 4-pin Grove connector, supports I2C and UART
- RGB LED and button
- Dimensions: 24 x 24 x 10 mm
- +5
Arduino Developer board Arduino Mega 2560 Rev. 3- Chipset: ATmega2560 (16 MHz)
- 54 digital inputs/outputs, 16 analog inputs
- Serial interfaces (4 pieces)
- 256 KB Flash memory, 8 KB SRAM and 4 KB EEPROM
- +1
jOY-iT SEN-HX711-20 Load cell up to 20kg- Integrated 24-bit A/D converter
- Serial 2-wire interface
- Measuring range up to 20 kg
- +77
Raspberry Pi Power pack USB-C 5.1 V 3 A White, Raspberry Pi 4- Output voltage: 5.1 V DC
- Input voltage: 100-240 V
- Maximum power: 15.3 W
- Nominal load current: 3.0 A
- 1.5 m 18AWG cable with USB-C connector
- Compatible with Raspberry Pi 4 Model B
- +13
M5Stack LED strip Digital RGB LED Strip SK6812 5 m- Programmable RGB LED strip with IP65 waterproof protection
- LED quantity: 300 LEDs
- LED strip width: 10 mm
- Lifetime: 30Kh
- Programming method: Arduino, UIFlow (Blockly, Python)
- HY2.0-4P adapter cable included
- +2
Whadda Temperature & humidity sensor CM2302 / DHT22- Measuring range temperature: -40 - 80 °C
- Measuring accuracy temperature: /- 0.5 °C
- Humidity measuring range: 0 - 99.9% RH
- Measuring accuracy humidity: /- 2% RH
- Operating voltage: 3.3 - 5.5 V DC
- Current consumption: 1.5 mA
- +8
Raspberry Pi Micro SD card 64 GB Noobs, for Raspberry Pi 4- Suitable for Raspberry Pi 4
- Memory: 64 GB
- Pre-installed «Noobs» operating system
- Micro SD to SD adapter included
- +6
Whadda Jumper set (m - m), 15 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 15 cm each
- Male to male
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +10
Raspberry Pi M.2 HAT+ for Raspberry Pi5- Equip your Raspberry Pi5 with an M.2 PCIe 2.0 interface
- M.2 M-Key interface for boards in the 2230 and 2242 form factor
- Compatible with NVME SSDs
- Maximum data throughput: 500 MB/s
- Including 16 mm spacer
- Compatible with the Raspberry Pi5, even with mounted active cooler
- +16
Raspberry Pi Developer board Pi Pico 2W- Based on the success of the original Pico, but with the brand new microcontroller chip: RP235x, created by Raspberry Pi in the UK
- With more powerful ARM cores, higher clock rate, SRAM and flash memory
- Features a new security architecture based on Arm TrustZone
- The Raspberry Pi Pico 2 offers improved performance and functionality while remaining compatible (hardware and software) with the previous models of the Raspberry Pi Pico family and their accessories
- Processor cores: Dual ARM Cortex-M33 cores
- Frequency: Up to 150 MHz
- +6
Raspberry Pi Micro SD card 32 GB Noobs, for Raspberry Pi 4- Suitable for Raspberry Pi 4
- Memory: 32 GB
- Pre-installed «Noobs» operating system
- Micro SD to SD adapter included
- +5
M5Stack Ultrasonic distance sensor RCWL-9620- Measuring range: 2 - 450 cm
- Accuracy: /- 2%
- Sensor type: RCWL-9620
- GPIO interface
- Dimensions: 56 x 24 x 15 mm
- Supports UIFlow
- +1
Whadda IR distance sensor for Arduino- Operating voltage: 3.3 V to 5 V
- Output: digital (on/off)
- Detection threshold: adjustable via 2 trim potentiometers
- Regulation R6: Set frequency 38 KHz (already optimized)
- Operating temperature: -10 °C to 50 °C, Detection angle: 35°
- I/O interface: 4-wire interface (- / / S / EN)
- +22
Raspberry Pi Micro SD card 128 GB Noobs, for Raspberry Pi 5- Suitable for Raspberry Pi 5
- Memory: 128 GB
- Pre-installed «Noobs» operating system
- +6
jOY-iT Developer board Node MCU ESP32- Tensilica LX6-Processor
- Integrated graphic: No
- Interfaces: I2C, SPI, UART
- +5
Raspberry Pi Housing for Raspberry Pi 4 Model B Grey/Black- Recesses for access to the connections
- Two-piece ABS construction
- Snap-in mounting - no tools required
- Dimensions (L x W x H): 97 mm x 70 mm x 25 mm
- Compatible with all Raspberry Pi 4
- +8
Arduino Developer board Arduino Uno SMD Rev3 Edition- Chipset: ATmega328 (16 MHz)
- 14 digital inputs/outputs, 6 analog inputs
- 32 KB Flash memory, 2 KB SRAM and 1 KB EEPROM
- Interfaces: USB 2.0, GPIO
- +17
Whadda Voltage regulator DC-DC Step-Up LM2577- With this module a DC voltage can be converted into a larger one
- Input voltage: 3.5 to 35 V DC
- Output voltage: 5 to 55 V DC (adjustable)
- Input current: Maximum 3 A
- Continuous input current: 2 A
- +22
Whadda Jumper set (m - f), 15 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 15 cm each
- Male to Female
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +5
Raspberry Pi Developer board Pi Pico2- Based on the success of the original Pico, but with the brand new microcontroller chip: RP235x, created by Raspberry Pi in the UK
- With more powerful ARM cores, higher clock rate, SRAM and flash memory
- Features a new security architecture based on Arm TrustZone
- The Raspberry Pi Pico 2 offers improved performance and functionality while remaining compatible (hardware and software) with the previous models of the Raspberry Pi Pico family and their accessories
- Processor cores: Dual ARM Cortex-M33 cores
- Frequency: Up to 150 MHz
- +2
Arduino Starter Kit Arduino Uno R3 French- ATmega-Processor
- Audio channels: None
- Integrated graphic: No
- Interfaces: GPIO, USB 2.0
- +10M5Stack LED strip Digital RGB LED Strip SK6812 0.5 m
- Programmable RGB LED strip with IP65 waterproof protection
- LED quantity: 30 LEDs
- LED strip width: 10 mm
- Lifetime: 30Kh
- Programming method: Arduino, UIFlow (Blockly, Python)
- HY2.0-4P adapter cable included
