Developer board accessories (363 results)
- +55
Raspberry Pi Power pack SC1152 5 V, 5A, USB-C, white, Raspberry Pi 5- USB-C PD capable: 5 V 5 A / 9 V 3 A / 12 V 2.25 A / 15 V 1.8 A
- 1.2 m long cable with USB-C connector
- Input voltage: 230 V 50 Hz
- Dimensions: 87 x 43 x 95 mm
- Ideal for the Raspberry Pi 5
- +28
Raspberry Pi Power pack SC1157 5 V, 5A, USB-C, Black, Raspberry Pi 5- USB-C PD capable: 5 V 5 A / 9 V 3 A / 12 V 2.25 A / 15 V 1.8 A
- 1.2 m long cable with USB-C connector
- Input voltage: 230 V 50 Hz
- Dimensions: 87 x 43 x 95 mm
- Ideal for the Raspberry Pi 5B
- +162
Raspberry Pi Housing SC1160 with fan Black, Raspberry Pi 5- Robust plastic housing
- Cut-outs for all connections
- Fan included
- Compatible with the Raspberry Pi 5
- +398
Raspberry Pi Active cooler SC1148, Raspberry Pi 5- Flat aluminum heat sink with fan
- Compatible with Raspberry Pi 5
- +448
Shelly Temperature sensor DS18B20 1-Wire- 1-Wire
- Accuracy (-10°C - 85°C): ±0.5°C
- 1 m cable
- Waterproof
SKU: 1018633Manufact. ID: Temperature sensor DS18B20 (1 meter)Category: Sensor developer boards CHF 4.65 - +4
jOY-iT Housing for Raspberry Pi 5 Aluminum, Black- Robust aluminum housing for Raspberry Pi 5 B
- Integrated passive cooling through milled channels on the top
- Direct contact to processor and RAM for maximum cooling performance
- Precisely fitting cut-outs for all connections of the single-board computer
- Elegant design in black
- Including thermal pads and screws for mounting
- +37
Whadda RFID card 10 piece- Frequency: 13.56 MHz
- Memory : 1 kb EEPROM
- Type: ISO14443 Type - A
- Operating temperature: -10 °C to 75 °C
- Can be rewritten up to 100000x
- +68
Raspberry Pi Micro SD card 32 GB Noobs, for Raspberry Pi 4- Suitable for Raspberry Pi 4
- Memory: 32 GB
- Pre-installed «Noobs» operating system
- Micro SD to SD adapter included
- +6
NewjOY-iT SBC-BuckBoost02 Voltage Regulator- Accessory type: Voltage transformer
- Output voltage from: 3 V
- Output voltage to: 25 V
- Input voltage up to: 25 V
- Input voltage from: 5 V
- +23
Shelly Leak sensor cable- Water detection over the entire cable length for comprehensive protection
- Flexible placement, also ideal for hard-to-reach places
- Direct connection with Flood Gen4 for immediate functionality
- High sensitivity and fast response time thanks to conductive materials
- Supports automations for switching off devices
- Reusable and easy to clean, simply wipe dry after the alarm
- +3
NewjOY-iT ESP32-C5 Radio Module- Dimensions: 53 x 27.8 x 4.8 mm
- Weight: 10 g
- Includes 2 x 15-pin male connectors
- +8
NewjOY-iT SEN-MQ3-V2 Gas Sensor- Compact Gas Sensor
- 2 outputs
- Molex 4-pin connector interface
- Maximum operating voltage: 5 V
- +42
Whadda Jumper set (m - f), 15 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 15 cm each
- Male to Female
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +9
NewjOY-iT SEN-MQ2-V2 Combustible Gas Sensor Alcohol Gas Sensor Board- Alcohol Gas Sensor Board for Developer Boards
- +10
NewjOY-iT MQ-2 Sensor board for flammable gases and smoke- Sensor board for detecting flammable gases and smoke
- +10
NewjOY-iT MQ-2 Sensor board for flammable gases and smoke- Sensor board for detecting flammable gases and smoke
- +10
NewjOY-iT MQ-2 Sensor board for flammable gases and smoke- Sensor board for detecting flammable gases and smoke
- Compact dimensions of 41 x 25 x 21 mm and a light weight of 8 g
- +10
- +2
NewKemo M227 Level Indicator capacitive- Precise and reliable liquid level monitoring
- Monitoring of Water and Slurry Tanks
- Can be used in cisterns
- Capacitive measurement principle that is resistant to contamination
- +41
Whadda Water pump 4.2 W, 5 - 12 V DC- Powerful mini water pump
- Voltage range: 5 V - 12 V DC
- Flow rate (maximum): 240 liters/hour
- Power consumption: 4.2 W at 12 V DC
- Outer diameter output / input 8 mm
- Lifetime: > 30,000 hrs
- +65
Whadda RFID Tag 5 piece- Frequency: 13.56 MHz
- Memory : 1 kb EEPROM
- Type: ISO14443 Type - A
- Operating temperature: -10 °C to 75 °C
- Can be rewritten up to 100000x
- +21
jOY-iT Housing Armor Case Block Active for Raspberry Pi 4B- Aluminum housing with integrated cooling body
- 2x 24 mm 5 V fan
- All connections remain accessible
- Including thermal pads and screws
- Suitable for Raspberry Pi 4 B
- +11
jOY-iT Voltage regulator DC-DC SBC-Buck02- Step-down converter with 5 V output
- Input voltage: 9 - 35 V
- Output voltage: 5 V
- Output current: max. 5 A
- Output power: max. 25 W
- Connection: 3-pin screw terminal
- +43
jOY-iT Raspberry Pi 5 DIN rail housing- Material: Plastic
- Compatible with Raspberry Pi 5
- Cut-outs for all connections
- Space for additional fixtures
- Transparent, removable panel for quick access
- Additional, transparent panel with integrated fan
- +64
Whadda Voltage regulator DC-DC Step Down LM2596S- Input voltage: 3 to 40 V DC
- Output voltage: 1.25 to 35 V DC
- Output current: Max. 2.5 A
- Chip: LM2596S
- Dimensions: 49 x 26 x 12 mm
- +24Whadda Jumper set (m - f), 30 cm 40 pins
- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 30 cm each
- Male to Female
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +16
jOY-iT Voltage regulator DC-DC SBC-BuckBoost01- Step-up and step-down function
- Voltage adjustable via trimmer
- Integrated segment display
- Maximum power: 25 W / 2 A
- +9
Whadda Relay module 4 Channel- Can be controlled directly via a microcontroller
- Status LEDs for relay output
- Control voltage: 5 - 12 V DC
- Maximum switchable voltage: 250 V AC / 30 V DC
- Maximum current: 10 A
- Dimensions: 75 x 55 x 19 mm
- +13
jOY-iT Housing Aluminum Black, for Raspberry Pi 5- High-quality, cast aluminum
- Milled channels that form a heat sink
- Cut-outs for all connections
- Dimensions: 91 x 65 x 34 mm
- Weight: 205 g
- Compatible with Raspberry Pi 5
- +19
jOY-iT Housing Raspberry Pi 4B Aluminum- Compatible with Raspberry Pi 4
- Robust aluminum housing for optimum protection
- Elegant design in silver
- +4
jOY-iT Touch screen RB-TFT3.2-V3: 3.2"- Display size: 3.2" (8.13 cm)
- Resolution: 320 x 240 pixels
- Touchscreen type: Resistive single touch
- Connection: GPIO header
- Brightness: 350 cd/m
- Dimensions: 85 x 20 x 60 mm
- +91
Raspberry Pi Power pack 5.1 V 2.5 A, micro USB, to Pi Zero 1 / 2, Pi 3B- Suitable for Raspberry Pi 3B / 3B / 3A / 2B / Zero / Zero 2
- Output voltage: 5.1 V DC
- Current: 2.5 A
- 1.8 m long cable with Micro USB connector
- Input voltage: 100 - 240 V AC 50/60 Hz
- +10
jOY-iT Heat sink RB-Heatsink-B Set for single-board computers- Cooling type: Passive (without fan)
- Accessory type: Heat sink
- Set: Yes
- +21
Whadda Jumper set (f - f), 15 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 15 cm each
- Suitable for standard plug-in boards (pitch: 0.1")
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +294
Raspberry Pi Power pack USB-C 5.1 V 3 A White, Raspberry Pi 4- Output voltage: 5.1 V DC
- Input voltage: 100-240 V
- Maximum power: 15.3 W
- Nominal load current: 3.0 A
- 1.5 m 18AWG cable with USB-C connector
- Compatible with Raspberry Pi 4 Model B
- +26
jOY-iT Motor driver SBC-MotoDriver2- Motor type: Brushed, DC motor, Stepper motor
- Accessory type: Adapter board
- Set: No
- +14
jOY-iT Jumper cable 20 x 25 cm, socket-socket, 40 pins- Color: Colorful
- Cable length: 25 cm
- Connection A: Wire jumper socket 20 x 1
- Connection B: Wire jumper socket 20 x 1
- Pins: 40
- +21
Whadda Jumper set (m - m), 15 cm 40 pins- A 40-pin multicolor flat cable
- Contains 4 pieces of 10 different colored wires each
- Length: 15 cm each
- Male to male
- Conductor cross section: 22-26 AWG
- Easy to connect and disconnect
Also available in: - +76
Raspberry Pi Power pack USB-C 5.1 V 3 A Black, Raspberry Pi 4- Output voltage: 5.1 V DC
- Input voltage: 100-240 V
- Maximum power: 15.3 W
- Nominal load current: 3.0 A
- 1.5 m 18AWG cable with USB-C connector
- Compatible with Raspberry Pi 4 Model B
- +33
jOY-iT Voltage regulator DC-DC SBC-XL6019- Accessory type: Voltage transformer
- Output voltage from: 5 V
- Output voltage to: 40 V
- Input voltage up to: 5 V
- Input voltage from: 35 V
- +4
jOY-iT Voltage regulator DC-DC SBC-Buck03- Current and voltage display on the module
- Constant voltage and constant current operation
- Adjustable output voltage from 0 to 32 V DC
- Maximum output power 160 W
- Input voltage range 6 to 40 V DC
- Fine resolution for voltage (0.01 V) and current (0.001 A)
- +21
jOY-iT Touch screen RB-TFT1.8-T: 1.8"- Display: 1.8" (4.57 cm)
- Resolution: 128 x 160 pixels
- Touch technology: Resistive
- Interface: SPI
- Compatible with Raspberry Pi, micro:bit, Arduino (3.3 V logic)
- Dimensions: 57 x 5 x 35 mm
